How to Repair Holes in Drywall

Drywall Repair Techniques

June 14, 2022 7 Read

Drywall repair is not rocket science. In fact, with a little bit of patience and the right tools, repairing drywall is something that most homeowners can handle themselves. Of course, there are always going to be exceptions to the rule, and some drywall damage is best left to the professional’s drywall repair. But, if you have a small drywall repair job that needs to be completed, follow these steps and you should have no problem getting the job done right.

Tools You’ll Need:

  • tape measure
  • drywall saw
  • utility knife
  • putty knife
  • drywall mud
  • sandpaper
  • joint compound
  • primer paint
  • paintbrush

Drywall compound is available in dry powder form or as a pre-mixed product. If you are new to drywall repair, it is probably best to use the pre-mixed compound. It is much easier to apply and will save you some time.

If you have a hole in the drywall that is less than 6 inches in diameter, you can simply use a drywall compound and a putty knife to fill the hole. For larger holes, you will need to use a drywall patch.

Fixing drywall is not a difficult task, but it does take a little bit of time. Be patient and take your time. If you rush the job, it will show in the finished product.

How to Patch a Small Hole

In repairing drywall, small holes are the easiest to fix. (For larger drywall damage, see our drywall repair tips.) All you need is a putty knife, drywall compound, and patching plaster.

Here are the steps for drywall installation and repair:

  1. First, use the putty knife to clean out any debris from the hole in the drywall. The wall surface should be clean and dry before proceeding.
  2. Next, apply joint compound to the area around the hole with your putty knife. A damaged drywall surface should be completely covered with a layer of drywall compound.
  3. Once the drywall compound is in place, take your patching plaster and apply it over the hole. Be sure to smooth out the plaster so that it is level with the surrounding drywall surface.
  4. Allow the plaster to dry completely before painting or wallpapering over it. If the drywall sheets are damaged, you may need to replace them entirely. For larger holes in drywall, you may need to use a drywall patch. Follow the instructions above, but before applying the patching plaster, place the drywall patch over the hole and secure it in place with drywall screws.
  5. Finally, once the drywall compound is dry, sand the area around the hole until it is smooth. Then paint or wallpaper over the repaired drywall surface. Large holes can be repaired using a drywall patch or by replacing the drywall sheets entirely. If you need to replace drywall, be sure to follow these drywall installation tips.

painting or wallpapering

How to Patch Medium Holes

In drywall, medium holes are approximately 6 inches in diameter or less. These holes can be caused by doorknobs, falling objects, and other accidents. If not properly repaired, drywall holes will leave your wall looking unsightly. You can patch medium drywall holes using a few supplies from your local hardware store.

What You’ll Need:

  • drywall patch
  • drywall screws
  • drywall knife
  • drywall mud
  • putty knife
  • sandpaper
  • paint (optional)

In patching medium holes in your drywall, you’ll first want to clean up the hole. Remove any drywall debris that may be left behind. If the drywall around the hole is crumbled, you’ll want to use a drywall knife to cut away the damaged drywall. Be sure not to make the hole any bigger than it needs to be.

After the hole has been cleaned out, drywall mud can be used to cover the hole. To do this, simply apply the drywall mud to the putty knife and then spread it onto the hole. Be sure to smooth out the drywall mud so that it’s level with the surrounding drywall.

Once the drywall mud has had a chance to dry, you’ll want to apply a second coat. Once dry, use sandpaper to smooth out the drywall mud. If desired, paint can be used to match the surrounding wall.

And that’s it! By following these simple steps, you can patch medium holes in your drywall.

How to Patch Large Holes

Drywall large holes are inevitable. No matter how careful you are, drywall is going to get damaged. Maybe the kids were horsing around in the hallway and accidentally punched a hole in the wall. Or maybe you just had a little mishap while trying to hang a picture. Whatever the reason, now you’ve got a hole in your drywall that needs to be repaired.

The good news is that drywall repair is actually pretty easy to do yourself. With a few simple tools and the right techniques, you can patch up a hole in your drywall in no time.

Here’s what you’ll need to do the job:

  • Drywall saw
  • Measuring tape
  • Drywall knife
  • Sandpaper
  • Joint compound
  • Putty knife
  • Trowel
  • Paper tape
  • Screwdriver

DIY repairs are easy with a few simple tools.

First, you’ll need to measure the hole. Use a drywall saw to cut out a square piece of drywall that’s about 2 inches larger than the hole. Unlike minor repairs, you’ll want to remove a large piece of drywall so that the patch will blend in with the rest of the wall better.

Next, use a drywall knife to score the back of the drywall square. This will make it easier to break the drywall so that it fits perfectly into the hole. Once you’ve scored the back of the drywall, break it along the scored lines and set it aside.

Now it’s time to prep the hole. Use your drywall knife to remove any drywall debris or chunks that are still clinging to the edges of the hole. Once the hole is clear, use sandpaper to smooth out the edges. This will make it easier to apply the joint compound and get a smooth finish.

Now you’re ready to start patching the hole. Begin by applying a generous amount of joint compound to the drywall square. Then press the drywall into the hole and use your putty knife to smooth out the edges.

Once the drywall is in place, use your trowel to apply a thin layer of joint compound over the entire patch. Be sure to feather the edges so that the transition from wall to patch is seamless.

Now it’s time to apply paper mesh tape. Unroll a strip of paper tape and press it into the wet joint compound. Use your putty knife to smooth out the tape and remove any air bubbles. Once the paper mesh tape is in place, apply another layer of joint compound over the top. Be sure to feather the edges as before.

Now all you have to do is wait for the joint compound to dry. Once it’s dry, sand the area until it’s smooth. Then apply a final layer of joint compound and sand it once again.

Once you’ve repaired the hole, you can paint over it to match the rest of the wall. With a little time and effort, you can patch up any drywall hole - no matter how big it is!

Hire Drywall Repair Professionals

Drywall is a material used to finish the interior walls of homes and businesses. It consists of panels made of gypsum plaster that are taped together at the seams and then covered with joint compound, or mud. Drywall repair is usually needed when there are holes or cracks in the drywall.

Professional drywall repair services can be hired to fix drywall problems. These services usually include repairing drywall seams, drywall cracks, drywall holes, and other damage.

Drywall repair professionals can also help with texturing and painting drywall. They can match the existing texture of the drywall or create a new one. They can also help to match the paint color to the drywall.

Drywall repair is not a do-it-yourself project. It is best to hire drywall repair professionals to ensure the job is done correctly.

Many drywall repair companies offer their services online. You can compare different companies and read customer reviews before choosing one to hire. Be sure to get quotes from several companies before making a decision.

Conclusion

After following the steps above, your drywall hole should be repaired and good as new! Those larger holes may take a little more time, but with some patience and elbow grease, anyone can do it. And remember, if the thought of drywall repair still intimidates you, there’s no shame in calling in a professional. In the end, what’s important is that the hole gets filled so that your drywall looks smooth and even once again.